(EN) REAR LOCKING ACTIONS
REAR LOCKING SYSTEM
The adoption of a strong rear locking system present the following advantages :
1°) Angle of pressure (forces transmission from casehead recess to the lugs):
-In a Front Locking system, the angle formed by the two (or multiple) Lugs bearing surfaces from the centre of the bottom of the case head recess is a very wide angle. On a certain common Fullbore action, ist is:
-98° at the root of the Lugs.
-112° at the outside diameter of the Lugs.
Possible slight variaions from one model to an other can exist, but is neglectible.
It can immediately be noticed that the forces spread at those angles creates a ‘flexling’ effect as the force is exerted at centre, and the hold on the outside as per the above angles.
-In a Rear Locking system, this angle is very shallow. On the INCH, it is:
-12° at the root of the Lugs.
-14° at the outside diameter of the Lugs.
It can immediately be noticed that this closed angle is creating a buttress effect, transmitting the forces in almost a straight line with the bore axis. No flexion, only compression forces that the generous cross sections over the length of the Bolt (and Receiver) compensates in harmony with no buckling possibility.
2°) Bolt Travel:
The transfer of the lugs to the rear allow an important reduction in Bolt travel:
On Front Locking systems, lenghtwise allowance must be made for the Bolt Lugs and Receiver Counter-lugs, that the Bolt head has to override to reach closure position. The cartridge to be chambered has to accomplish the same increased movement.
-On the Rear Locking system, the Lugs are situated behind the Loading Port, and the cartridge can be fed directly.
-On the same Front Locking Action of reference (Short Action) hereover mentioned, the Bolt travel is 107mm, (4.210’), when it is only 85mm (3.346’) on the INCH, the later allowing also longer cartridges cases (all magnums).
This also have a big influence in Cheekpieces profiles and heights possibilities, as this reduced Bolt travel impairs much less the cheekpiece position.
3°) Bolt Face and feeding:
-The absence of necessary cuts to ensure the Lugs shape allow to have a perfectly cylindrical Bolt Head, surrounding entirely the cartridge head. This has also allowed the use of a wider extractor.
-Cone breach was the obviosu solution, not easily achieved in front locking designs. The feeding of a round, moreover thanks to the absence of Lugs raceways, is the smoothest possible.
The absence of lug recess at front and easy access to chamber is important in cleaning as residues or dirt cannot accumulate as they are easily removed with no specific tools.
L4°) ugs arangement
-The Rear Locking of the INCH allowed a specific Lugs disposition, as, when closed, each Bolt Lug is situated geometrically, with one lug at top (12 O-clock when closed), and the two lowers symetrically in the horizontl plane (4.30 and 7.30 O-clock respectively),. This mean that each Lug is situated behind a consequent section of the Receiver, and also backed by a circular strong secrtion of the Body behind them..
This is to compare with the Front Locking 3 lugs design, where one of the lugs is always immediately ahead of the Loading Port, or, in the case of a two Lugs design, bearing vertically in the axis of two uneven side sections, the R/H one (RH action) being considerably reduced by the Loading Port cross section.
5°) Barrel Shank:
-The INCH reduced Bolt travel allow a significant increase of barrel shank lenght (35mm-1.378’), however keeping the action the shortest of its category (187mm –7.368’ OAL).
Two closely toleranced cylindrical registers, one behind the threaded middle part, the other at front centers the barrel, the middle threaded section acting only as what a thread is intended for: screwing and tightening/securing.
This arrangement makes the barrel changes extremely easy, and with absolutely no zero shift.
Also, the inside collar allow a double bearing of the barrel shoulders: against the Receiver front face, AND against the inside collar. Shoulders bearing surface is at least 30% more than a conventional fitting bearing on the Receiver front face only.
On the subject of easy barrel interchange, the generous dimensions of the Delta Lugs arrangement allow an excellent holding area for the short Action whrench designed also as a occasonal rod guide.
R.G.C
06/2009
Inscrivez-vous au blog
Soyez prévenu par email des prochaines mises à jour
Rejoignez les 85 autres membres